Tips for Click water-resistant flooring installation installation: (forbid using something heavy to knock the lock catch floor)

1. Environmental requirements before laying the floor

1. Ground or subfloor flatness:Pls use 2m gradienter to detect flatness,the permitted maximum gap should not over 2mm within 2m,if not,pls use proper self-leveling cement to make level.

2. The moisture content of floor: Detect the floor dry by CM basic level moisture meter, the moisture content of basic level is required to be less than 6%.

3. Air temperature and humidity in workplace: Temperature hygrometer was used to detect temperature and humidity. The room temperature shall be kept between 15-25℃, when below 10 ℃ or above 30 ℃, construction shall be banned and the indoor relative air humidity shall be between 20% and 75%.

4. Ground surface hardness: surface hardness which is tested by hardness testing device shall not be lower than 1.2 Mpa.

II. Preparation before construction

1. 48 hours before construction, unpack the product and place it with auxiliary materials at the construction site to adapt the ambient temperature and relative humidity and make it in agreement with the temperature of the construction site to prevent expansion and shrink after construction. The product shall be piled horizontally to prevent bending deflection of the floor.

2. Plan carefully and appropriately cut the ground. (The length of single room can not exceed 10m and the width can not exceed 8m. 10 mm expansion seam shall be left all round.)

The tool used for installation: 2m guiding rule instrument, CM moisture detector, graving instrument for surface hardness, temperature hygrometer, paper knife and so on.

Routine maintenance of floor

1. First clean the blot on the floor. There is glue or sticky on the floor, use neutral cleanser and cloth to wipe the dirt. 

2. Splash special cleanser for the floor (use according to the instruction) on the floor. Use wax-polishing machine to wipe the dirt on the floor, then use dry top to absorb the water, and then use clean water to wipe the floor. (If there is no wax-polishing machine, use other tools to wipe the dirt)

3. When the floor is clean, pour water-borne water on the clean and dry mop, and then coat the floor with wax uniformly.

4. After waxing for about 20 min, make the floor surface air drying. When the floor is dry, stand on the floor and use fax to blow the floor to reduce time. Generally, the floor will be totally dry within a few hours after being waxed. If something quite heavy needs to be moved, wait until the wax is dry. The floor can be kept bright in this way.

The above-mentioned 4 procedures are common cleaning methods. After using the floor for a period, the floor is flavescent and needs to be waxed again after being waxed for a few times, use wax remover to solve the problem. The methods are shown below:

1. Use the wax remover in proportion, splash it on the floor where the wax needs to be removed uniformly. After 10 min to 30 min, the wax remover is penetrated into the floor. Use water to brush the floor blush (if there is no wax machine). The wax needs to be removed completely, or the floor will not be bright.

2. After the wax is removed, clean and maintain the floor according to the above-mentioned 4 procedures.

Maintenance tools and raw materials: vacuum cleanser, absorbent cloth, clean machine (wax-polishing machine and mop) and cleanser.

Attentions:

1. Place the ground mat on the door and passageway to avoid the ash, grit and soil scratching the floor.

2. While carrying the articles, especially the article that has sharp metal on the bottom, don’t drag the article.

3. While cleaning the floor, don’t use steel wool or steel brush. Consult professionals for the dirt which can’t be removed in routine method. Don’t use chemicals arbitrarily, such as acetone, methylbenzene and strong acid.

4. Avoid large amounts of water on the floor surface for a long time,  If the floor is soaked by water, water may be penetrated under the floor. The floor can be warping, which substantially influence the service life. (Mucilage glue will dissolve the floor glue and the floor glue may lose the bond force). Warping floor may cause the wax and water in different layers, polluting the floor, or the color of the floor may be changed because sewage penetrate in the inside floor (transparent floor).

5. Avoid direct radiation of strong light and prevent radiation of ultraviolet to avoid the color of th floor is changed or faded.

6. Keep the temperature and humidity of the air: indoor temperature shall be kept between 15℃ and 25℃ and humidity between 20% and 75%. Pay special attention to the negotiability of the indoor air. Don’t keep the indoor sealed for a long time. (Especially in the holidays of the summer)